ower | Patriots

Do-It-Yourself Metal Framed and Encapsulated Solar Panel

~~ NOTICE ~~

This is NOT a free book. You may NOT forward this book to anyone else. You do NOT have resale rights for this book. We will take aggressive legal action against anyone violating these terms. If you have purchased this book from anywhere other than the main product website, including eBay, please inform us right away.

2012 © Copyright 2-1 See www.power4 patriots.com www.power4 patriots.com/shop

Legal Disclaimer

The authors and publishers both disclaim liability regarding any loss or risk incurred as a direct, or indirect, consequence of the application and usage of any of the contents within this Do It Yourself (DIY) instructional material.

Copyright

Those who have received or purchased the DIY instruction manual are neither authorized nor permitted to transmit copies of this file to anyone without written permission. Giving away copies to people who haven’t paid for them 1s illegal under international copyright laws and will submit you to possible legal action. Therefore, the utilization of this file is limited to personal use only.

Power4Patriots.com Terms & Disclaimer

By using, viewing, and interacting with the DIY guide or the Power4Patriots.com website, you agree to all terms of engagement, thus assuming complete responsibility for your own actions. The authors and publishers will not be held liable or claim accountability for any loss or injuries. Use, view, and interact with these resources at your own risk.

All products from Power4Patriots.com and its related companies are strictly for informational purposes only. While all attempts have been made to verify the accuracy of information provided on our website and within the publications, neither the authors nor the publishers are responsible for assuming liability for possible inaccuracies.

The authors and publishers disclaim any responsibility for the inaccuracy of the content, including but not limited to errors or omissions. Loss of property, injury to self or others, and even death could occur as a direct or indirect consequence of the use and application of any content found herein.

Working on home improvement projects and with renewable energy sources is dangerous. Since you are dealing with electricity, high roof tops or towers, and numerous other unknown conditions, seek expert opinions and help where necessary. The authors and publishers assume that, while carrying out your DIY project, you are aware of all the risks and possible damages associated with home improvements and renewable energy.

Check with your town, city, state, province, county or country for applicable laws about home improvements and alterations. Often, it is necessary to obtain local government permits and licenses to prevent legal implications. We also recommend that you call your local electrician, and other professionals, to assist in your DIY projects. Failure to do so could cause injury or death - you are acting at your own risk.

Before performing any home improvement or renewable energy project you should first check with your insurance carrier, homeowners association or any other persons or associations that may need to approve such work. Insurance coverage and premiums may be affected by home alterations and so you need to check with your insurance agent first. All Power4Patriots.com information is intended for adults above the age of 18 years only.

By choosing to use the information made available by Power4Patriots.com or within any of our publications, you agree to indemnify, defend, and hold harmless the authors, publishers, and any other related companies from all claims (whether valid or invalid), judgments, suits, proceedings, losses, damages, and costs or expenses of any nature whatsoever that result from the use or misuse of any information provided.

The information provided may need to be downloaded using third party software, such as Acrobat or Flash Player. It’s the user’s responsibility to install the software necessary to view such information. Any downloads, whether purchased or given for free from our website, related websites, or hosting systems, are done at the user’s own risk. No warranty is given that websites are free of corrupting computer codes, viruses or worms.

If you are a minor, you can use this service only with permission and guidance from your parents or guardians. Children are not eligible to use our services unsupervised. Furthermore, Power4Patriots.com specifically denies access to any individual covered by the Child Online Privacy Act (COPA) of 1998.

Remember...Safety First!

2012 © Copyright oe See

www.power4 patriots.com www.power4 patriots.com/shop

Table of Contents

Section 2

Do-It-Yourself

Metal Framed and Encapsulated Solar Panel

I MEFOCIUICIIOIN capes cskceodege eee sn sesenta et aodennteonee teenage s semanas. 2-4 SOM SEROICTION (MOLC CS oorperarcesctd aecetedagaqnicteendcrmanenesaicesatonslcas 2-5

Upgrade Option #1: Building a Metal Frame................ 2-5

Upgrade Option #2: Encapsulating the Cells ............... 2-6

Upgrade Option #3: Using Tempered Glass................. 2-/ SOUCING VOUP IWATETIANS ic asicisaesairennabentststanancdiabsegnatinaisanbardeawt 2-8 SOlal PaNelGONSMUCTION 2 sncvescarccesetssascasezoxecsietesdseaneaneesece 2-10 "TEOO IS AUC IAC ANG aera pacientes ee see 2-11 STEP #12 ODialll SOlal COS casecncssceueanuctweebosneacarenadenbones 2-12 STEP #2: Determine Your Desired Panel Output............ 2-15 STEP #3: Determine the Panel Dimensions.................... 2-16 STEP #42 DUNG UNS FAM C iariiccuicccccusenee’dcomancegucescnce sadeuecses 2-17 STEP #5: Cut the Glass Pane for the Panel.................... 2-20 STEP #6: Solder Cells Together ..................cccccccsseeeeeeeees 2-22 S LEP #f. POUl ENCADSUIGIC sii onaienisanddnanciesnivaneesnncaeoande: 2-26 STEP #8: Lay Strings of Cells on Glass .................cc:cece 2-28 STEP #9: Lay Back Sheet & Attach Angle Aluminum ..... 2-31 1 ee Oe AGG IUMCliON BOX seccseecacareesnecatescetmeaneaanestie 2-33 STEP #11: Remove Air Bubbles and Test in the Sun..... 2-34 Analyzing your Solar INVeStMent ...............cccceceeeeeeeeeeeeeees 2-36 Weighing the Pro’s And COn’S .............cceccseeeseeceeeseeeeeeeeees 2-38 OMG SION wise c age tesa soncesane sect ascbesecesdcnvaceseeenaneeseaotess 2-40

2012 © Copyright os See

www.power4 patriots.com www.power4 patriots.com/shop

Introduction

As thousands of homeowners are taking the energy crisis into their own hands by building their own solar electric panels there are some choices that must be made before beginning your project. Obviously, with the ability to customize the panel to meet any current or voltage parameters that you may require there is the choice as to what output you will want your panel to have. By wiring the panel with more cells in series, or choosing cells with higher current output, you can build one panel that may match the needs of a wide variety of batteries, water pumps, brushless DC fans, etc.

There are the obvious dimensional choices, too. You can build your panel in any shape or size; whether it is to minimize space of the array, fit strange angles on your roof, or to fit within a frame that you have bought or found to use for your panel. The panels can be built as rectangles, squares, or even triangles to suit your needs. What most people don’t know, however, is that there are choices to be made in how you choose to construct the panel, regardless of the panel’s output or dimensions. This decision will ultimately determine your panel’s effectiveness.

Longevity of the panel and your budget are the two major factors involved in making the decision concerning which construction method to use. The two are, in fact, quite related. By investing in better materials for building the frame of your panel, and by taking the necessary steps to protect the cells from the damaging elements you can build yourself a panel that will last several times as long as a panel built with a minimalistic approach. This will increase your initial investment into your solar panel, but you will get much more power in the long run, at a lower

cost per kilowatt hour produced from your panel.

2012 © Copyright ae See

www.power4 patriots.com www.power4 patriots.com/shop

Construction Choices

When you set out to build your solar panel, there are 3 main upgrade choices. Each will give your panel more strength and protection from the elements and each will all add a bit of cost to your initial investment. Each upgrade can be done independently from the other 2 options, so you can choose to add strength and protection for your panel by choosing just one of the upgrades below, or you can opt to make all 3 upgrades for the most professionally built panel

possible.

Upgrade Option #1: Building a Metal Frame

Your first option for adding strength and longevity to your solar electric panel involves the construction of the frame. With the “Under $98 Solar Panel” the frame is made with wood. While the wood is sealed with primer and paint, the protection from the elements — mainly rain and sun — is not sufficiently adequate to protect the panel for more than a few years. Insects can also find a home in a wooden frame, further speeding up the decomposition process. In addition to the eventual rotting of the wood, the actual construction process itself creates more spacing for water and insects to get inside the frame, where the cells would then be negatively affected.

By choosing to upgrade to a metal frame, and in our case an aluminum frame, you give the panel extra protection by encasing it inside of a frame which will stand the test of time against the rain and sun. The beauty of aluminum is that is won’t rust, making it ideal for the frame of a panel which will be exposed to the rain and placed under as much sun as possible. Not only will using aluminum provide extra protection from the elements and provide better strength overall, but it will provide fewer weak spots in the design of the frame where insects could burrow into

and multiply. The beauty of this upgrade is that it will not add too much cost to the panel. Since

2012 © Copyright a See

www.power4 patriots.com www.power4 patriots.com/shop

metal provides more strength than scrap wood pieces, not as much aluminum is needed and no

painting needs to be done, keeping the extra money spent very minimal.

Upgrade Option #2: Encapsulating the Cells

With the “Under $98 Solar Panel” the cells are wired together and then attached to a substrate behind them. This is not a bad option; however it leaves the cells exposed to the elements. No matter how hard you try to seal the frame to keep all of the weather elements out, eventually some moisture will get behind the front glass and into your frame and the cells will collect the moisture. Any exposure to the weather elements on the part of the cells will lower the output and degrade the cells faster than they should degrade.

The best way to protect the cells from the elements — and a method that is possible to do in your backyard — is to encapsulate them with a liquid silicone. This liquid silicone, when mixed with its curing agent, hardens into an optically clear rubber-like polymer. This silicone hardens around the cells, completely encapsulating them to the glass and completely protecting them from the elements. While the commercial solar panel manufacturers encapsulate their cells in EVA sheets, the vacuum sealing machines for this method make this unfeasible for your backyard project.

On the other hand, the liquid silicone, produced by Dow Corning under the name “Sylgard 184 Silicone Elastomer Kit” can be bought through one of their distributors and in the quantity necessary to build just one panel. This method will add no more than $40 or $50 to your final costs for the project and is the main factor in increasing your panel’s estimated lifespan from

around 5 years up to 25 years or more!

2012 © Copyright ~ See

www.power4 patriots.com www.power4 patriots.com/shop

Upgrade Option #3: Using Tempered Glass

By upgrading from regular single pane glass for the front of your panel to tempered glass you add a lot of strength to your panel. Tempered glass is much stronger than regular glass. It can withstand begin hit with hail, flying debris or other objects without the likelihood of breaking as you would find with regular glass. Glass can be tempered by washing it in a chemical bath or by superheating the glass until it is just below its melting point and then uniformly spraying it with cold water. This rapidly cools the outside of the glass while the inside remains hot, creating the tempered structure of the glass.

The major downside of this upgrade is that it can be very costly. Tempered glass cannot be cut once it has been tempered, so you would have to cut the glass to size and then temper it. The problem with this approach is that tempering glass must be left to the professionals, and it can be costly. Unless you plan on placing an order for hundreds of pieces, you may find yourself paying over $100 just for one 2’ x 3’ piece of glass to be tempered.

If you plan on placing your solar panel in an area where falling branches or debris are unlikely to land on your panel, and you plan on taking your panel inside or covering it when a hail storm looms then you should be just fine with regular glass. The tempered, low iron glass used by the commercial solar panel manufacturers is just too costly for a small-scale backyard project. The big manufacturers place orders for thousands of tempered glass pieces at a time, which is why they can even afford to temper their glass to begin with. If you are just looking to build a few small panels and you cannot find any flat tempered glass that would work for you then go ahead and use single pane glass and simply place your panel in a location where it is less likely to break. For the sake of this guide, we will be building a panel that uses the single pane

glass, but does include the metal frame and encapsulated cells upgrades.

2012 © Copyright oe See

www.power4 patriots.com www.power4 patriots.com/shop

sourcing Your Materials

Once you have determined the method for constructing your panel, you will need to go ahead and begin to source the location for these parts. While the majority of the materials needed for building your aluminum framed and encapsulated solar cell panel can be found at your local hardware store, some important materials, such as the solar cells and encapsulate must be ordered through distributors or from online vendors. The chart below lists the materials needed

for constructing the panel, what you should expect to pay, and where to source these materials.

Metal Framed / Encapsulated 65 Watt Solar Panel

Tabbed Solar Cells www.shopDIY Energy.com Encapsulate Glass Cover Aluminum Angle | 3 8 it it

$

Metal Corner Braces | G4 Hardware Store

Aluminum Channel

3 se -7-

Blocking Diode

it 14 $4 Flux Pen www.shopDIY Energy.com Bond Paper Plastic Back Sheet Terminal Strip Hardware Store Plastics Glue | $l | Hardware Store Silicon II Sealant*

ssf

(*note that some prices reflect not using the entire amount of the materials — example: the Silicone II Sealant was $6/tube yet only 1/3 is needed = $2/panel)

= = Cm

It 1s important to note that the prices listed above are only to be used as a reference since both costs and availability of materials can vary with time. However, with the right ideas and a

little hunting you can certainly get what you need for under $200. Consider how many panels

2012 © Copyright = See

www.power4 patriots.com www.power4 patriots.com/shop

you are preparing to build, too, as the price per item — such as the solar cell — can drop when you order larger quantities. One panel will need 36 cells, but you should consider buying a few more as they are very breakable. If you plan on building 3 panels you will have more purchasing power and could get a better price for buying 3 times as many cells at once.

Another way to save money on the solar cells is to buy them untabbed. It will require more time to solder on the tabs yourself, and you may break a few more solar cells in the process, but the savings can justify this. The cost of the extra tab ribbon needed (figure one foot per cell) is marginal and will not offset the savings from buying untabbed cells.

A big reason that DIY solar panels have been gaining popularity in recent times is the availability of traditionally hard-to-find materials on the web. In the past, the majority of the population did not have access to solar cells or hard-to-find electronic components. However, with the rise of online vendors and auction sites like eBay everyone with a valid shipping address can buy whatever materials they need to build a solar panel that rivals any commercial solar panel in performance and durability. That said, anything you can source locally should be sourced locally to avoid any shipping costs. You may think you are getting a great price on a deep cycle battery online, but when adding shipping costs to a heavy battery it may become more expensive than to buy it locally despite whatever deal you may think you are getting.

If you don’t need to build your panel right away, you may want to begin doing research online for the best prices for the solar cells. Many of the “buy it now” options ensure the quickest transaction on the online auction sites such as eBay, yet many times you end up paying retail. Try searching for cells or other materials early on in the process and bid on the item for a lower cost. While you may not win the item for the low price you seek if you have time to do this on

several items you should end up saving yourself some money.

2012 © Copyright a See

www.power4 patriots.com www.power4 patriots.com/shop

Buying broken or blemished cells may save you considerable money, too, but make sure that you are buying cells you can work with. Blemished cells many times will have the same output as non-blemished cells just with minor aesthetic issues. If you buy chipped or cracked cells you will want to make sure that the remaining pieces are large enough to work with. If you open the box and find only tiny little pieces you will have nothing to work with. For the purpose of this guide we will be using 3” x 6” solar cells without and cracks or chips, but if you find a good deal on cells with tiny chips or cracks they will work. Just remember, the current output 1s directly proportional to the size of the solar cell, so if the chip or crack is too large then your cell’s output will be lower than the rest and will bring down the power output of the entire panel.

In any case, don’t attempt to buy solar cells from a vendor that does not offer shipping insurance — especially if they are selling chipped cells which can break further on transport quite easily. The cells are very fragile, so you want to ensure that 1f you open your package of cells

and most of them are broken you can get your money back.

Solar Panel Construction

Currently, the limiting factor for widespread adoption of solar is the initial cost of the completed solar system. While a typical solar system will consist of many components, the solar panels often comprise more than 50% of the entire cost. This accounts for thousands of dollars even in the smallest of residential cases. Solar panels, when made yourself can be done for a fraction of the cost of what is available commercially and can ultimately save you a lot of money, whether you opt for building a small 65 watt solar system or for wiring several panels

together and creating a larger system. Even with no experience and limited access to tools

2012 © Copyright aa See

www.power4 patriots.com www.power4 patriots.com/shop

anyone can learn how to build a fully functional PV panel and can begin producing energy from

the sun in just a few hours. For the purpose of this DIY panel we will be dealing with crystalline

cells and the following 1s a basic guideline in what steps to take, which methods to employ and

which tools to use to build your own metal framed and encapsulated solar cells panel.

Tools and Materials

As stated before, most of the following tools and materials can be sourced locally. The rest

can be found online and through national distributors than ship via USPS, FedEx or UPS.

Viaterials

Solar cells and tabbing wire Bus wire

Encapsulate

Respirator

Eye Protection

Multimeter

Aluminum Channel and Angle Metal Corner Angles

Solder Gun and Solder Caulk Gun and Silicone Caulk

2012 © Copyright a

www.power4 patriots.com

Hacksaw

Metal File

Vacuum Hand Pump Rivet Gun and Rivets Clamps

Clear glass panel cover Latex Gloves

Flux Pen

Miter Box

Carpenter’s Square

see www.power4patriots.com/shop

STEP #1: Obtain Solar Cells

Solar cells are measured by their power in watts. To obtain a cell’s wattage you must first know how many volts, represented by V, and amps, represented by A, the cell has. Amps are commonly measured in current, represented by I. To determine its watts, represented by W, you multiply the volts by the amps. This formula can be expressed as V x A = W. If the voltage and amperage are unknown, you can measure it with a multimeter that will take both current readings up to at least 10 amps and voltage reading of up to 600 volts.

Take your measurements in full, constant sun. You can hold the cell perpendicular to the sun and contact the multimeter’s negative and positive probes to the negative and positive electrodes on the cell. You may opt to construct a solar tester using a highly conductive backing, such as a copper plate. This will provide a steady place to rest the cells for measurement and will only require you to touch the positive probe from the multimeter to the metal backing instead of

the cell itself.

2012 © Copyright me See

www.power4patriots.com www.power4patriots.com/shop

MAKE A TESTING BLOCK

Get a copper plate

- large enough to COPPER PLATE FACE |

rest cell on

- small enough to “ee allow cell to a

iclileme) (21m (ole

2012 © Copyright ala See www.power4 patriots.com www.power4 patriots.com/shop

A solar cell will have a voltage right around 0.5 volts, but may read upwards of .6 volts in direct sun. Its current reading will vary dependant in its size. For example, a 3’ x 6” solar cell may read .5 volts and 4 amps under full sun. If you were to cut that cell up into four equal pieces, you will have four cells that each still read .5 volts, but now each one has just 1 amp. Be very careful in your handling and measuring of the cells, as they are extremely thin and very fragile. Measure all of your cells to make sure that you are only going to be using the best cells for your solar panel. Less desirable cells should be put aside with the broken cells for future projects that don’t require very much power. This is an important step, especially if buying blemished, broken or used cells off of the internet since if just one cell has a low current rating it will bring down the current of the rest of the cells it is wired in series with. Remember, when wiring in series the voltages add, but the current remains the same, and will only be as strong as its weakest link. Measuring the current is more important than measuring the voltage, since each cell will be close to .5 volts even with blemishes or chips.

Going back to the previous example with the 3” x 6” cell cut into four pieces we will now see just how customizable a solar panel can be. The solar cell started with a rating of 0.5 volts at 4 amps. By cutting it into quarters we have 4 cells of .5 volts and 1 amp. Now, if we were to wire these cells together 1n series we will have a string of cells with 2 volts (.5 volts x 4) and 1 amp. If we were to wire these cells together in parallel, we would have a string of cells with .5 volts and

4 amps. All of this can be done with just one cell. The same concept applies to wiring panels

together. SERIES vs PARALLEL WV, 1 a, Series adds Parallel adds voltage, amps/current 2-14 2012 © Copyright See

www.power4 patriots.com www.power4 patriots.com/shop

STEP #2: Determine Your Desired Panel Output

If you are trying to charge a 12 volt battery it 1s advisable that you build a 16-18 volt panel. To build an 18 V panel (as we are to do) you need 36 cells in series. This is determined because 36 cells wired in series at .5 V each will give us 18 V (36 cells x 0.5V = 18V). Again, you may have cells that have a higher voltage than 0.5, but building a panel with 36 cells 1s still good practice.

The current rating of the panel will be the same as the rating of just one solar cell, in this case 3.5 amps, assuming they are all wired in series. If you desire higher amperage you can wire two strings of 36 cells together in parallel to double the amperage in a given panel to have an 18V and 7A panel, or you can simply wire two 18v and 3.5A panels together in parallel to achieve the same purpose. Keep in mind size and weight limitations, not to mention breakability when determining the power output of your panel. Building a large panel with a glass frame may

increase the likelihood that the glass may get cracked in the future.

OF) Os Cl Ey Wal lem Je)!" AMPS (A) x VOLTAGE (V) = POWER IN WATTS (W)

CURRENT (1) |S COMMONLY MEASURED IN AMPS

MEASURE INDIVIDUAL CELLS amps A volts = watts

MULTIPLY # CELLS BY VOLTS cells X volts V panel =a

MULTIPLY PANEL VOLTS BY AMPS amps X V W panel

a

at

2012 © Copyright on See

www.power4 patriots.com www.power4patriots.com/shop

STEP #3: Determine the Panel Dimensions

This is done by some simple math. First, take the dimensions of your individual solar cells, in our case 3” x 6”. There are two main panels layouts that you may wish to work with. The first and the one we will outline are 4 rows of 9 cells wired together. The other option is to use 3 rows

of 12 cells, as illustrated below on the right.

SOOLAR PANEL LAYOUT OPTIONS

3s x iz

4a x Ww

Figure 1

Working with the example of the 4 rows of 9 cells, we need to determine the width and length of the panel. If each cell is 3” x 6” and there are 4 cells wide we will need at least 24” (6” x 4 = 24”). Typically you will want to allow at least 14” in between the rows, so add 34” to the width (1A” x 3 = 34”). Then add an inch on the right and left sides and you are left with 24 34”. We'll round this up to 25”. Do the same math to determine the height. (9 cells high x 3” each) + (8 spaces in between the cells X 14’) + (3” — allow more spaces along the tops and bottoms of the panel for wiring the individual strings of cells together) = 32”. That leaves us with 25” x 32”.

This is the dimension necessary for the inside of the metal frame.

2012 © Copyright alae See

www.power4 patriots.com www.power4 patriots.com/shop

It is important to note that this is the minimum size for your panel. If you find a precut piece of tempered glass or a metal frame that 1s a little larger than the dimensions given that you can work with it, just add more spaces in between the cells or along the edges. The important part is that you provide enough space within the inner dimensions of the panel frame for all of the cells. Perform the same calculations for a panel comprised of 3 rows of 12 cells but make

adjustments as necessary.

Step #4: Build the Frame

For building the metal frame aluminum is the best choice. One, it holds up very well against the weather elements and 1s very rust resistant. Second, it is lightweight and easy to work with. All this comes at a very competitive cost. For a 65 watt panel you will need about 10 feet of Aluminum stock C-channel. The actual measurements are 1” x 9/16” x 1/16”. This can be found at any local hardware store and should cost less than $15 for the entire length. While at the hardware store, you should also pick up the aluminum angle. You will need about 8 feet of the angle stock at 1/2” x 1/2” x 1/16”. This aluminum angle will be used later.

Measure out the aluminum channel to fit outside of the solar cells. Take your measurements from earlier from the inside of the metal frame and then add the depth of the aluminum channel. This will give you your outside dimensions of the panel. For this guide we built the outside dimensions at 26” x 33”. Measure out 2 pieces at 26” and 2 at 33”.

Use a miter box to make perfect 45 ° angles on each C-channel. Make sure you make the cuts so that all four pieces when lined up will create a rectangle with the C-channel facing the

inside of the panel.

2012 © Copyright ame See

www.power4 patriots.com www.power4 patriots.com/shop

OO

The corners will be held together with rivets and metal angles pieces. Use a small piece of wood with holes drilled into it as a template for drilling into the aluminum. This will ensure that the corners are riveted together nice and tightly, will line the holes in the aluminum to the holes

in the metal angles and will save you time for lining up the other 3 corners.

Use a carpenter’s square to line up the two sides of the frame you are going to join to make sure they form a perfect 90° angle. If the angle is too far off then the frame will not be a rectangle and your last corner will end up off. Once you have lined up the pieces of the first corner then proceed to rivet the aluminum C-channel to the metal angles. This will join the frame

pieces together and will add the strength from the metal angles.

2012 © Copyright aks See

www.power4 patriots.com www.power4 patriots.com/shop

It is important to make sure that you only attach 3 of the sides together before sliding the glass inside. If you attach all four sides together you won’t be able to fit the glass inside the closed off channel. It is also important to know that if you do make any mistakes in the rivets placements you can remove the rivets with a drill. Simply use a small drill bit and drill into the center of the exposed rivet. This will allow you to pop off the rivets and realign before proceeding with the rest of the panel construction.

2012 © Copyright oer See

www.power4 patriots.com www.power4patriots.com/shop

If you have cut the angles with a miter box and they still don’t seem to align correctly when lined up with the carpenter’s square then use a metal file and file it down to match correctly. Once you do have two frame pieces that line up well mark the inside of the channels so that you can remember to match those two up later. Take your time with this step, as the strength

of the panel depends on good, tight rivet connections and flush angles.

STEP #5: Cut the Glass Pane for the Panel

The most important part of this step is to remember to wear protective gloves and eye wear. Cut glass can be extremely sharp, and when the glass breaks extremely small shards of glass can become airborne. If cannot find a piece glass that matches your need requirements, and you don’t want to pay extra to have someone else cut the glass for you, it can be done right at home and is quite easy.

Glass cutting kits can be bought at your local hardware store for just a few dollars. With a very straight edge you will want to score the glass along the line that you want to cut the glass. Tap underneath the glass to ensure the score line penetrates the width of the glass. Hold the glass over a very straight edge, line up the score with the edge of the table and apply even pressure to the part of the glass that is hanging off the table.

If the line has been scored adequately the glass will break smoothly along the line. This may require some practice, so I would recommend getting some smaller pieces of glass to test your technique. Also, be sure that the dimensions of the cut glass 1s made to fit within the inside dimensions of the aluminum frame. Since the aluminum channels are 1/16” deep, the two

channels on either side of the frame will combine for a 1/8” total. If you measure the frame from

2012 © Copyright — See

www.power4 patriots.com www.power4 patriots.com/shop

the outside and cut the glass to match you will cut your glass 1/8” to wide and 1/8” too long. Account for the added depth of the aluminum channel and your glass will slide into the frame smoothly.

After you have cut the glass and before you have slid it into its frame place a bead of caulk around the inside channel of the frame. Make this bead along the inside of the front edge of the panel. This will give a better seal between the glass and the frame to protect from any water

entering the frame of the panel from the front glass.

Slide the glass into the frame very carefully and with gloves. Once the glass 1s all the way inside the frame and contact has been made between the caulk bead and the glass on all 3 sides attach the final side. Rivet the corners like before and make sure the angles are square. This is where you will be able to tell just how square you got the other 3 corners. Don’t forget to put the

bead of caulk on the last side before riveting it into place.

2012 © Copyright > See

www.power4 patriots.com www.power4patriots.com/shop

STEP #6: Solder Cells Together

If you have pre-tabbed cells (the ones with the thin tab ribbon coming off of the face) you will only have to solder the cells together at the back, or negative side. If untabbed, apply solder to the tab ribbon and connect the tab ribbon to the front bus bars that run from the bottom of the cell all the way to the top of the cell on the negative side. You will have to do this twice for each 3” x 6” cell as you will have two bus bar strips. Allow enough tab ribbon lead to come off of the cell to attach it to the back side of the next cell in series, roughly twice the height of your cell.

Once you have 36 cells with tab ribbon coming off the face of the cell you will want to begin soldering the cells together in series. A good trick here is to build a template for the cells so that the solar cells are evenly spaced apart and when you are soldering they will not move very much. A template can be made with tile spacers attached to a piece of plywood. Measure

carefully and attach a tile spacer in the spacing between each solar cell.

2012 © Copyright mon See

www.power4 patriots.com www.power4patriots.com/shop

Lay each cell in place to begin connecting them in series. Each cell will be laying face down with the tab ribbon leads coming off in the same direction. Apply a little bit of flux to all six exposed electrode rectangles on the back of each cell with your flux pen. This will help draw

the solder onto the cell and will make a stronger solder joint.

Once the cells have been fluxed take your solder gun and apply a little bit of solder to each tab ribbon. This will save you time when connecting the tab ribbon to the back of the next cell. Use a solder pen (seen in black in the picture below) or similar object to keep the tab ribbons in place and apply a press the ribbon down onto each exposed electrode that you have pre fluxed.

Do this along each string of cells until you have connected each string of cells in series.

2012 © Copyright ee See

www.power4patriots.com www.power4patriots.com/shop

Once each string is completed, cut a strip of tab ribbon to attach to the back of the first cell in each string. This will ensure that you have tab ribbon leads coming off each string. You will need tab ribbon leads on both ends of the strings to connect each string together with bus ribbon

when on the glass.

2012 © Copyright nae See

www.power4 patriots.com www.power4patriots.com/shop

When all of your strings are wired together go test them in the sun to ensure the series connections were done properly. If there is a problem in one of the strings this is your best chance to isolate it and fix the issue before the cells and all connected on the panel and the

encapsulate has been poured.

2012 © Copyright : See www.power4 patriots.com www.power4patriots.com/shop

STEP #7: Pour Encapsulate

Take out the Sylgard 184 Silicone Elastomer Base and its Curing Agent. You will want a clean container to mix the two chemicals together and something to stir 1t with. A Food Saver jar works especially well since it can be capped with a hand pump attached to it to vacuum the air

bubbles out of the mixture.

The 0.5 kg kits are the perfect amount for one panel, although with some practice you can get by with using only 90-95% of the kit per panel. Take the entire contents of the Curing Agent and slowly pour it into the container with the Elastomer Base. It is very important that you completely mix the two together so that the curing process is even throughout the panel. Using your stirring rod and mix the contents for about 5 minutes or so. The mixture should bubble as

the mixing is done.

2012 © Copyright oe See

www.power4 patriots.com www.power4patriots.com/shop

Once the encapsulate has been mixed you will have a few hours before the solution starts to harden, so you can take your time and do it correctly here. The bubbles that emerge in the mixture will eventually be transferred to the panel and become bubbles on the face of the glass if they are not removed. By vacuum sealing the jar with the mixed encapsulate inside you pull the air out of the container and the air bubbles will naturally draw out of the mixture. The container should ideally be vacuumed 29 Mercury (Hg) of pressure, if possible, to remove all of the air bubbles from the mixture. If you cannot achieve 29 Hg of pressure in the container and some

bubbles remain you will have the opportunity mitigate the bubble factor later on.

Take the frame with the glass attached inside and lay it on a perfectly flat table. Make sure it is completely flat, for if 1t at a slight angle your cells will end up all on one side of the glass. You may want to place a piece of plastic underneath the glass to protect the table, as some of the encapsulate may leak out during the curing process. Pour a little bit of the encapsulate over the glass. The cells will then be placed on top of this encapsulate. Only use a little, however, as you will want to save most of the encapsulate for pouring over the cells once they are on the glass.

2012 © Copyright i See

www.power4 patriots.com www.power4 patriots.com/shop

STEP #8: Lay Strings of Cells on Glass

Take each string a place it down on top of the glass. The encapsulate you have already poured will help keep the cells in place while you do the final soldering. Make sure to lay each string so that are in opposite directions from each other. In other words, if the first string has the positive leads coming off the top then lay the next string so that the negative leads come off the top. This will allow you to wire each string together in series with the bus ribbon. Remember, the tab ribbon coming off the backs of the cells are the positive leads, and the tab ribbon coming off

the front of the cells is the negative leads.

Wire the strings together with bus ribbon to ensure you have a completed series connection throughout all 36 cells. You will also want to wire bus ribbon from the two “home runs” to the center-top of the panel. The home runs are the two tab ribbon leads that come off either end of the completed string. They will be in the top left and top right of the panel if you are working with a 4 row by 9 cell configuration.