The Touch Code Lock consists of a keyboard and a console The keyboard sends a coded signal from outside the garage The console fastens lo an Inside garage wall It receives the 4-digit programmed coded signal and starts the door opener The Touch Code Lock will work with most Genie “Push Twice to Operate” openers if you press any other digit after you enter the 4-digit programmed code. NOTE: CABLE CONNECTOR HOLE iS LOCATED ON LEFT SIDE OF CONSOLE IF POSSIBLE, INSTALL TOUCH CODE LOCK ON LEFT SIDE OF GARAGE (DETERMINED BY FACING GARAGE FROM OUTSIDE) IF INSTALLED ON RIGHT SIDE OF GARAGE, CABLE MUST BE ROUTED OVER OR UNDER CONSOLE FEATURES OF THE DIGITAL TOUCH CODE LOCK Personalized Code: 10,000 possible combinations Code can be changed easily if desired. Operation: Opener activates when programmed code is entered on the keyboard The user has 10 seconds from the time the first number is pressed to enter the 4-digi! code if incorrect numbers are accidentally pressed, a 5 second interval is necessary before starting over. Power Supply: Operates from the garage door opener power with a battery back-up for code memory and light¬ ed keyboard Unit will not operate without battery Installation: Simple to install in 5 easy steps Console: Provides an additional push button control to operate door from inside garage Keyboard: The garage door can be operated after a valid code entry by pressing ANY single key AS LONG AS THE KEYBOARD LIGHT REMAINS ON. Keyboard Illuminates and remains lit for 10 seconds when ANY number is pressed. In darkness this feature allows user to press ANY number before entering the 4-digit code IMPORTANT NOTE: When illumination is needed, avoid pressing keyboard area which contains the first code number. DISCONNECT THE POWER TO THE GARAGE DOOR OPENER BEFORE BEGINNING INSTALLATION. STEP 1—SECTIONAL DOORS: Draw two intersecting lines on garage jamb face—horizontally at eye level and vertically as close to centerline as possible Make sure there is at least 1-1/4” clearance on each side of the vertical tine. Drill a 1" diameter hole through the jamb at marked location. Refer to illustration on Side 2 if your garage has a built- up jamb. Keyboard Door Jamb Face PARTS LIST Console Assembly Keyboard Assembly 9 Volt Battery 2 Strand Beil Wire , , Transformer Kit (inc belt wire) 41D2940 4ID2952 . 10A13 213A276 41A3468 STEP 1—ONE-PIECE DOORS: Install the keyboard on the exterior front wall of a FRAME garage Position it away from the door opening to avoid injury as door swings out and up Drill a 1" diameter hole through wall at eye level. Refer to note below; then proceed to Step 2 NOTE: If garage is constructed of material other than wood {brick, stone or aluminum siding), install keyboard on door jamb with this important exception: LOCATE KEY¬ BOARD ON OUTSIDE EDGE OF DOOR JAMB TO AVOID INJURY AS DOOR SWINGS OUT AND UP, NO USER SERVICEABLE PARTS. For repair, contact a SEARS Service Center Side 1 NOTE: If your garage has a built up jamb, drill the hole 2" deep. Then, on inside edge of jamb, drill a second hole into first hole to complete access STEP 2: Hold keyboard firmly with She back of the case UP. Position thumb against bottom of case and pull up sharply. Keyboard will lift out of cover, allowing access to bottom mounting hole Guide the keyboard cable through hole to inside of garage. Position the keyboard against outside jamb Drill two 1/8" pilot holes for fastening screws. Attach securely with (2) 6ABx1-1/4" screws Close cover Excess cable can be folded and inserted into the access hole to keep it out of the way STEP 3: Connect the 2-strand bell wire to terminals labeled 1 and 2 on back of console. Insert keyboard cable connector into slot on side of console Be sure connector guides are facing BACK of console. IMPORTANT: Some garage door openers have a third screw terminal which supplies power to the radio control. This terminal can be connected to terminal No. 3 on the console with a third strand of bell wire (not supplied). With any garage door opener made by Stanley, accessory transformer kit 41A3468 MUST be installed. TRANSFORMER INSTALLATION INSTRUCTIONS: Connect one end of the 2-strand bell wire supplied with the kit to each of the transformer terminals Polarity is not important Con¬ nect the other end of bell wire to terminals 1 and 3 on the Touch Code console IF THIS ACCESSORY IS USED WITH ANY GARAGE DOOR OPENER OTHER THAN SEARS OR CHAMBERLAIN AND THE BATTERY FAILS IN TWO MONTHS, TRANSFORMER MUST BE INSTALLED. Follow instructions above. STEP 4: Position console on an interior garage wall approxi¬ mately one foot from outside edge of door. Fasten with (2) 8ABx1" screws Run bell wire up wall and across ceiling to garage door opener terminals Use insulated staples to secure wire Cut off any excess wire Connect to terminals used for push button controls. On Sears models, connect wire as follows; Mode! series 53000—to red and white terminals Model 664400—to blue and white terminals Model 664000—to red and black terminals. All other models—to white and white terminals or to the terminals used for wall push button STEP 5: Pry open front panel of console with a coin or screw¬ driver. Snap a 9 volt battery onto circuit board connector and drop into console DO NOT replace panel at this time STEP 6: To set code, move program/operate switch near the battery to PROGRAM position (keyboard light should flash).. NOTE: If the light does not flash, check the cable and bat¬ tery connections. Press any four numbers on keyboard, CAUTION: For security, do not use address, license or consecutive numbers {1,2,3,4 etc.). Move the program/operate switch to OPERATE position (the keyboard light will go off) Reconnect power to garage door opener If you have installed Transformer Kit 41A3468, plug the transformer into a 120 Volt outlet. Enter the code on the keyboard. If the door oper¬ ates properly, replace the front panel on the console Loss of power to either the battery or the garage door opener will not affect the programmed code. However, if BOTH lose power, the code must be reset. Battery should produce adequate power for at least one year If light in keyboard does not turn on, change the battery. NOTE: To maintain the privacy of your code, keep all of the buttons free from soil. If any of the numbers show signs of wear, change your code. 114A113S Side 2 Printed in Mexico